HBL5450UC/09 How to program a Bosch oven

Hello

I have this bosch which is not heating right after replacing the main board a while back. The change fixed the over heat problem but at the time it was never programmed and i think this may be the problem with it now. I seem to remember that there was a program to go through when replacing the board but can't come up with it now. Would any of you have the procedures to do this if there is such a thing! Thanks for anything!!

via HBL5450UC/09 How to program a Bosch oven
by gordiel

Dacor Range RSD30S oven door hinge issue

The oven door is not aligned correctly and it appears one of the hinges is bent. I purchased the hinges and am now trying to change them. The issue is that I cannot remove the door. The hinge release lever is suppose to move upright over part of the hinge but it is also damaged, plus one of the hinges is bent in a way that it would not fit over the release lever. Is there any way I can release the hinge from the oven in order to remove the door? Thanks!

via Dacor Range RSD30S oven door hinge issue
by Paul1

CGSR362G2 Capital Culinarian oven overheating

This gas oven has had an overheating issue since almost new.

I have had Capital’s tech out three times and he has replaced the thermostat each time.

Yesterday, after the repair tech replaced the mechanical thermostat for the third time, I attempted to bake some cookies at 375. I use an external thermometer to monitor the oven temp and after smelling the cookies burning I checked the temp and thermometer was maxed out, over 510 degrees.

From my understanding of mechanical thermostats...

CGSR362G2 Capital Culinarian oven overheating

via CGSR362G2 Capital Culinarian oven overheating
by Russell Jones

GE Profile - Igniter blew, then display failed

Our GE Profile, model PGB995SET1SS, had a bad igniter in the lower oven. I bought a non-OEM replacement and installed it with ceramic wire nuts provided. It tested fine. Next time it was used (by S.O.) she said there was a pop and a fizzle sound, then control panel went out. I checked breaker and it had not tripped....I flipped breaker for 30 secs, reset, no difference. Checked igniter and it was in many pieces. Lights still work, stovetop and upper oven work fine. Any suggestions?

via GE Profile - Igniter blew, then display failed
by Freeflynick

Bosch Wall Oven HBL5450UC/06 display error

Hi, I have a Bosch HBL5450UC/06 wall oven. For the past few weeks, it would revert to the setup menu, as if there had been a power failure, even when there was none. You could re-enter the setup info, hit the "Info" button, and all would be well for a while until it reverted to the setup again. Now the problem is much worse.

The display will revert to the setup menu, and the system will allow you to enter data, but when you hit the Info button, the display only shows 4 vertical bars in...

Bosch Wall Oven HBL5450UC/06 display error

via Bosch Wall Oven HBL5450UC/06 display error
by lakeguy55

Bosch HBL5450UC/06 display error

Hi, I have a Bosch HBL5450UC/06 wall oven. For the past few weeks, it would revert to the setup menu, as if there had been a power failure, even when there was none. You could re-enter the setup info, hit the "Info" button, and all would be well for a while until it reverted to the setup again. Now the problem is much worse.

The display will revert to the setup menu, and the system will allow you to enter data, but when you hit the Info button, the display only shows 4 vertical bars in...

Bosch HBL5450UC/06 display error

via Bosch HBL5450UC/06 display error
by lakeguy55

QS136WW Broan range vent hood shutting off

our broan allure QS1 series fan motor shutting off after 10 minutes after waiting for few minutes i turn on switch it will start again but still shuts off , motor overheating? do we need to change the motor?

via QS136WW Broan range vent hood shutting off
by djd12

broan range vent hood shutting off

our broan allure QS1 series fan motor shutting off after 10 minutes after waiting for few minutes i turn on switch it will start again but still shuts off , motor overheating? do we need to change the motor?

via broan range vent hood shutting off
by djd12