Dacor Oven DR30D/NG - Broil Element Needed

Broiler on Decor oven (DR30D/NG) has gone bad. Broiler part 700713 has been replaced by Samsung part DE81-07354A. Problem is that the part has been on "backorder" for 10 months. Concern that it will not be made again. Suggestions? Is there another broiler that will work for this model?

via Dacor Oven DR30D/NG - Broil Element Needed
by markfo

GE Profile JT952SK4SS convection wall oven will not heat past 100 degrees. Regular Bake/Broil works fine. Have replaced in the past element, sensor.

Have also turned the breaker off for a minute. Do I need to replace the element again? Is the control panel since the bake/broil work just fine. Thank you in advance.

via GE Profile JT952SK4SS convection wall oven will not heat past 100 degrees. Regular Bake/Broil works fine. Have replaced in the past element, sensor.
by mariedelvalle

Dacor Range ER36D - Igniters not working (all of them)

Hi There

I was gifted a Dacor ER36D range and it has been fantastic to date.

That said, last night all six ignitors stopped working. This seems a bit strange and I am curious if anybody has experience addressing this issue. My limited research shows that there are 6 ignition modules supporting the burners, but it would be highly unlikely that all six would fault at the same time.

Could there be an inline fuse or something that needs replacing?

via Dacor Range ER36D - Igniters not working (all of them)
by Dan.w716

Kitchenaide kgsa906 not staying lit

So I have been having issues with my range
Now and then it will light and run fine and then other times it will click 3 times light and then go out
I cleaned the burner tube , replaced the igniter
Checked ohms on gas valve , both 195 ohms
Checked volt on dsi was 120
And vdc was 10.5
I am racking my brain to figure this out any help will be great
Thank you

via Kitchenaide kgsa906 not staying lit
by jchaplin

Montgomery Ward Range KSD2405 oven won't light

I can't find anything online about the range (slide-in, propane, about 30" wide) at my mom's house.

The pilot is lit, but when you turn the oven on, the pilot gets bigger but the main oven valve doesn't open.

The pilot thermocouple attaches at a valve below the oven burner and there's no "red button" anywhere.

Is this a bad thermocouple situation? Thanks!

via Montgomery Ward Range KSD2405 oven won't light
by ningersoll

Montgomery Ward KSD2405 oven won't light

I can't find anything online about the range (slide-in, propane, about 30" wide) at my mom's house.

The pilot is lit, but when you turn the oven on, the pilot gets bigger but the main oven valve doesn't open.

The pilot thermocouple attaches at a valve below the oven burner and there's no "red button" anywhere.

Is this a bad thermocouple situation?

Thanks!

via Montgomery Ward KSD2405 oven won't light
by ningersoll

LG relay control panel

I have replaced the relay control panel. My question is, do the black wire and the gray wire go together like I have it or do they need separated? When I took it off the little black box was burnt and I only remember one connector.

via LG relay control panel
by Brewru

Thermador Range PC486GEBS/01 - Need help with changing potentiometer

I need to change the potentiometers on my Thermador PC486GEBS/01 cooking range.
After removing the turn knobs and their trim there are no other screws left but the face plate
still feels connected to the range and not budging. Called Thermador and they said they don't provide any help
with self repair nor do they have any manual/video.

Can someone please help me figure out how I can remove the face plate of this model to replace the potentiometer??
The videos on YouTube showed how to remove...

Read more

via Thermador Range PC486GEBS/01 - Need help with changing potentiometer
by samPull

Thermador pc486gebs/01 - Need help with changing potentiometer

I need to change the potentiometers on my Thermador pc486gebs/01 cooking range.
After removing the turn knobs and their trim there are no other screwsleft but the face plate
still feels connected to the range and not budging. Called Thermador and they said they don't provide any help
with self repair nor do they have any manual/video.

Can someone please help me figure out how I can remove the face plate of this model to replace the potentiometer??
The videos on YouTube showed how to...

Read more

via Thermador pc486gebs/01 - Need help with changing potentiometer
by samPull