GE oven won't ignite

My pilotless electric ignition GE oven won't ignite. The broiler and gas stove-top both work fine. The manual says to make sure the switch in one of the attached pictures is flipped to "on," which it is and it is still not working.

Attached Thumbnails

     

via GE oven won't ignite
by jsil

Samsung oven wonÂ’t hold temp

Recently temps is dropping after reaching desired temp. For example set oven for 400, reaches 400 then basically shuts heat off while reading 400. Within 5-10 mins oven drops 200degrees and doesnÂ’t click back up to get back up to 400. Temperature used to go up by 4s and now goes up one degree at a time. I checked the temp sensor that is in the oven and its reading about 1000ohms, google tells me this is good. Im not very electronically savvy but i checked ohms on other wired items and came across this that registered 0 ohms and have no idea what it is....any insight

Attached Thumbnails

     

via Samsung oven wonÂ’t hold temp
by Jimmy6240

BOSCH HGS7282UC Self Clean not heating

Morning,

Self Clean feature on BOSH HGS7282UC is not functioning. The door Locks and the broiler ignites and it runs through timed cycle, so oven latch switch should be functioning. However the oven burner does not light, pulled bottom panel and igniter for oven does not turn on. I tried unplugging and same issue. Also verified resistance of oven temp sensor (1083 ohms at room temp, 2 ohm increase with hand on sensor). The oven burner ignites and functions in baking mode, so igniter is functioning. Is there a way to test both the power module and the display control kit, assuming problem is with one of them.

Thanks
Joe

via BOSCH HGS7282UC Self Clean not heating
by Joe F

Kitchen aid oven wont light because the DSI tries to light my back left burner instead of oven .....

Hello I have something a little strange happening with my kitchen aid gas range. A few weeks backs I noticed the oven wouldn't come on or would randomly work but more than often just the spark clicking and that's it . So I looked into it and weirdly enough when called upon to bake or broil instead of the spark happening in the oven the spark is happening at the cooktop and tries to light my left back burner which goes on and on like this so I did some troubleshooting and saw that there was smell of gas in oven so I know the gas valve does indeed works but I wouldn't not get my 120 volts at between J1-4and J1-6 on my DSI spark module and 120 volts was not present so I deducted that the ERC board wasn't sending the 120 volts to the DSI ( spark module ) so I went and bought the ERC board feeling pretty confident that would resolve my problem but no same problem still happening anyone as ran into something similar id love to put this issue to rest. I would believe my DSI board to be ok has once in a while the oven does come on and works fine but its pretty random and now that I replaced the ERC board I am puzzled could it be the board behind the clear language display ( touchpad) the graphics shows the proper operation I want but...… The wiring harness didn't seem to show any wear or anything defective I should also mentioned that after installing that ERC board today I also noticed that even when tricking the oven with the door open to run it I have yet to see the convection fan running yet on the display it clearly tells me its on though I am not sure if those two problems are related other than I thought the ERC took care of fan operations and also the oven operations and that the DSI literally just sparked and that it does but its being sent the wrong info as to where to spark I feel and if not from the ERC why is this happening ?

I am a refrigeration mechanic so I fix refrigerators mostly industrials and commercials but I also dabble into residential and I also hold my commercial gas license so its not like a complete boob doing this myself but without any proper tech sheets ( which I cant seem to find for this model ) its been a bit tricky. :)


thanks in advance I hope someone ran into this issue before

via Kitchen aid oven wont light because the DSI tries to light my back left burner instead of oven .....
by sheppard12

Samsung convection fan making a terrible noise

Well, Samsung oven sat here for awhile before we finally got our house finished and the appliances put in place. Technically, it's a titch over a year old, but I haven't had it installed near a year yet. The convection fan is hitting on something. When I open the door and the fan slows, I can hear it ping on something. I have the single door that can be two doors if the divider is installed in the oven, so I'm currently only using the upper part of the oven (if that makes sense). I don't think it matters, frankly, top or bottom at this point. I think it would make noise regardless. Anyone else with this problem? We are extremely tentative to remove it from its spot because they had a heck of a time getting it placed on the granite....Hopefully there's a way to check for the problem without having to pull it all the way out. Either that, or I won't use it anymore and just stick with the regular gas oven heating. Appreciate any help you can give me.

via Samsung convection fan making a terrible noise
by colbran

VGR48-6G Viking Range Specs

I have a 30 year old Viking range -- model VGR48-6G -- that needs to be replaced. Unfortunately I have lost the spec sheet and need to know the depth of the unit. When my kitchen was renovated the builders put in a special cut out to accommodate the range, so I can't just measure the visible depth. Can anyone help?

via VGR48-6G Viking Range Specs
by newpaulp

Viking Range Specs

I have a 30 year old Viking range -- model VGR48-6G -- that needs to be replaced. Unfortunately I have lost the spec sheet and need to know the depth of the unit. When my kitchen was renovated the builders put in a special cut out to accommodate the range, so I can't just measure the visible depth. Can anyone help?

via Viking Range Specs
by newpaulp