Thermador PG364GD Outer glass broken on oven door

My house came with a Thermador PG364GD. Last year, the outer glass was broken on the door. We tried ordering a replacement door from Sears, but after several delays, they cancelled the order altogether. My husband and I are looking for either another pane of glass, another oven door, or a new oven. Nobody can seem to find a door and the repair/appliance store in our town said that we didn’t have a complete model number. This appliance is 20 years old. Is it possible and worth it to get a new oven door, or should we just buy a less expensive range?

via Thermador PG364GD Outer glass broken on oven door
by Ware3315

Oven element substitution

The element has burned out on my Thermador electric oven. Thermador no longer makes or carries the part, and I cannot find it anywhere online (ebay, etc.), after months of searching.

My question is this: can I substitute another element of the same or slightly lesser wattage? It is either that or throw away a $4,000.00 oven. I can drill a few additional holes for supports if needed.

Thanks in advance for your help!

via Oven element substitution
by Ads321

LSWS305ST LG Wall oven Thermostat AND thermal fuse

Hello, I am in need of help.

My LG wall oven blew a thermal fuse a few years ago after a self clean. I did not use the self clean cycle again.

Since then, the thermal fuse has blown 2 more times, and the thermostat (another fuse type one on the back of the unit) has failed twice. I have had to take my oven out of the wall 4 times. This is getting frustrating to say the least.

One thing i notice is that each fuse I remove has melted plastic near the leads (the metal tabs that you connect the wires to). This does not look like it melted from external heat (the rest of the plastic on the fuse is fine). I will post a photo.

Is there something else that could be causing these repeated failures? How would I go about diagnosing this?

HELP. I am sick of pulling the oven out. Yesterday it happened when i tried to use the oven on convection bake at 450 degrees. :mad:

Attached Thumbnails

 

via LSWS305ST LG Wall oven Thermostat AND thermal fuse
by phemfrog

Outer glass broken on oven door

My house came with a Thermador PG364GD. Last year, the outer glass was broken on the door. We tried ordering a replacement door from Sears, but after several delays, they cancelled the order altogether. My husband and I are looking for either another pane of glass, another oven door, or a new oven. Nobody can seem to find a door and the repair/appliance store in our town said that we didn’t have a complete model number. This appliance is 20 years old. Is it possible and worth it to get a new oven door, or should we just buy a less expensive range?

via Outer glass broken on oven door
by Ware3315

GE Profile Wall Oven shuts off intermittently , also will lock itself too during cool down

I have a double wall oven, GE Profile, convection top oven. When pre-heating it will shut itself off sometimes. Also while cooling down it will go into a locked mode. No error codes appear. Just had repairman here, he was a kid, and just said it needs a new board and that's basically $600 all in. Just wondering what you all know about this model and if you think it's the board or something else? Thanks

via GE Profile Wall Oven shuts off intermittently , also will lock itself too during cool down
by Jenniferalovett

LG Wall oven Thermostat AND thermal fuse

Hello, I am in need of help.

My LG wall oven blew a thermal fuse a few years ago after a self clean. I did not use the self clean cycle again.

Since then, the thermal fuse has blown 2 more times, and the thermostat (another fuse type one on the back of the unit) has failed twice. I have had to take my oven out of the wall 4 times. This is getting frustrating to say the least.

One thing i notice is that each fuse I remove has melted plastic near the leads (the metal tabs that you connect the wires to). This does not look like it melted from external heat (the rest of the plastic on the fuse is fine). I will post a photo.

Is there something else that could be causing these repeated failures? How would I go about diagnosing this?

HELP. I am sick of pulling the oven out. Yesterday it happened when i tried to use the oven on convection bake at 450 degrees. :mad:

Attached Thumbnails

 

via LG Wall oven Thermostat AND thermal fuse
by phemfrog

Thermador SC302ZP Wiring Diagram? Top oven won't heat during convection

Have a Thermador SC302ZP/01 double wall oven. It is top convection. On "bake" it seems to work fine. On "convection" it will not heat up (fan runs). Any ideas? Or does anyone have a service manual/wiring diagram for this model?

via Thermador SC302ZP Wiring Diagram? Top oven won't heat during convection
by wabbastang

Whirlpool oven won't light without starting a stove top burner

Hello,
My Whirlpool wfg320m0bb oven will often not light/or relight without turning on a stove top burner. The issue has been happening for quite a while and I've replaced the igniter once already. The igniter appears to work properly, it comes on quickly and burns bright orange/yellow. But on many occasions, the oven flame does not come on (even after many minutes of waiting). If this happens and I turn on one of the stove top burners, the oven flame comes on immediately. The same thing happens when a relight of the oven burner is required to maintain the oven temperature. There was also a period of many months where even if the oven burner did light, the flame was extremely small. The resulted in the oven heating very slowly. This issue seems to have corrected itself, but I wanted to mention it in case it would help with the diagnosis. Thanks!

via Whirlpool oven won't light without starting a stove top burner
by Choppin

Viking stove sparking problems

I have a Viking range 15+ years old. For a while I had spotty ignition of the stove burners, sometimes had to try 2 or 3 times before I got a burner lit. Last week I spilled some soup into the stove, in the area of the spark module, and now it's gone haywire.

No matter which burner I turn on, only the left two burners spark, and then they keep sparking even after the flame is lit. (even if it's one of the left burners that are lit. the right hand burners I now have to light with a long-handled lighter because there is no spark on the right side.) I removed the cover over the spark module, and did a trial and error by moving around the wires heading to the burners. It was always the burners connected to the two righthand spark terminals that were continuously sparking, and the burners connected to the two lefthand terminals would not spark. Thought maybe there was some dried soup gumming it up, but the module and connections look clean. (it was very watery soup)

The sparks for the broiler and the bake function work fine.

Thinking I should just buy a new spark module but is there something else that could be wrong?

Thank you.

via Viking stove sparking problems
by Greenpointman

HBL5750UC/08 Bosch Wall Oven. Broiler element comes on / stays on in all cook modes.

Bosch wall oven, microwave combo, HBL5750UC/08

Problem:

• In any cook mode but off, broiler element comes on and stays on. This used to happen intermittently, now all the time.
• Eventually the over-temp sensor will trigger and turn it off.
• Turning oven to "off" will turn off broiler element.

• Built-in diagnostics (from downloaded service manual) don't show any relevant faults.
• Temp readings from sensors (again, using built-in diagnostics) seem accurate.
• Using diagnostics to turn on broil element turns it on, but again, will never turn off.

All of this leads me to believe it is a stuck relay?

Question:

I've seen references to a "control/relay board" and a "relay board". I suspect one of these components.

Control/Relay board comes up as Bosch part #12022212. This board looks like it has many small relays on it.

Relay board comes up as Bosch part #00663802. This looks more like a power supply board than a relay board.

Should I replace the relay board?

Attached Thumbnails

   

via HBL5750UC/08 Bosch Wall Oven. Broiler element comes on / stays on in all cook modes.
by pfbzzz

Kenmore Elite Oven Error

I have a Kenmore Elite 790.48033800. It is a common problem for the display to begin to fail. The digit segments start to fade till you can't see anything or only part of the digits that are being displayed. After this the oven started to error displaying either E95 or E96, it was hard to tell since the digit are fading. This occurred more and more frequently till now it happens every few minutes.

Has anyone ever tried to diagnosing the control boards out of any of the Kenmore elite ovens? I can get a replacement board but want to try fixing it first.

via Kenmore Elite Oven Error
by bigolbug

Bosch Wall Oven. Broiler element comes on / stays on in all cook modes.

Bosch wall oven, microwave combo, HBL5750UC/08

Problem:

• In any cook mode but off, broiler element comes on and stays on. This used to happen intermittently, now all the time.
• Eventually the over-temp sensor will trigger and turn it off.
• Turning oven to "off" will turn off broiler element.

• Built-in diagnostics (from downloaded service manual) don't show any relevant faults.
• Temp readings from sensors (again, using built-in diagnostics) seem accurate.
• Using diagnostics to turn on broil element turns it on, but again, will never turn off.

All of this leads me to believe it is a stuck relay?

Question:

I've seen references to a "control/relay board" and a "relay board". I suspect one of these components.

Control/Relay board comes up as Bosch part #12022212. This board looks like it has many small relays on it.

Relay board comes up as Bosch part #00663802. This looks more like a power supply board than a relay board.

Should I replace the relay board?

Attached Thumbnails

   

via Bosch Wall Oven. Broiler element comes on / stays on in all cook modes.
by pfbzzz

PRG364GD Thermador Gas Range two left burners not working?

Old Range where everything is still working except the two left burners. The back left burner will light and stay on for about 3 minutes then shutoff and won`t relight until it cools down.
The front right burner will click to light but no gas is flowing to the burner.
I do wonder if they still make parts for these ranges?

via PRG364GD Thermador Gas Range two left burners not working?
by goodeats

Thermador Gas Range two left burners not working?

Old Range where everything is still working except the two left burners. The back left burner will light and stay on for about 3 minutes then shutoff and won`t relight until it cools down.
The front right burner will click to light but no gas is flowing to the burner.
I do wonder if they still make parts for these ranges?

via Thermador Gas Range two left burners not working?
by goodeats

GE induction range shuts down

My GE induction range will periodically completely shut down, oven and stove top. I check at least once a month to make sure it's not in sabbath mode but it still shuts down. After and hour or so once everything has cooled off it will start back. I triped the breaker to see if that would start it back but all I got was and error code FA00. I really like how it cooks and cleans up but this is so frustrating I'm thinking I will buy another range.

via GE induction range shuts down
by Tatty2

Samsung FER300SX will not maintain temperature

All, I’ve read the following thread: https://www.applianceblog.com/mainfo...light=Fer300sx and I’ve replaced both the temperature sensor and the board. However, the problem is still occurring. I can set the temp for 350, and ten minutes later come back and the temp still reads 350 but if I turn the oven off and then back on the temperature started anywhere between 280-300. Replacing the parts brought that up to 310-315 but everything I read states the temperature should not vary more than 15 degrees either side of the set temp. Any other ideas?

via Samsung FER300SX will not maintain temperature
by joshuajack

HIIP054C Bosch oven meat probe not recognized

The meat probe on my VERY expensive Bosch HIIP054C slide-in induction oven does not register when it's plugged in (usually...there's the odd time where it comes on after being plugged in and the oven has been cooking for a while).
I gather I'll need to test the connectivity of the female socket in the oven, but wonder whether the probe might have gone bad. (I have never put it in the dishwasher or under water).
Any advice on how to get started?

via HIIP054C Bosch oven meat probe not recognized
by Entangler

control panel removal for Kitchenaid kesc308lss0 range

Looking for help removing the control panel for the above appliance. The display is not working but everything else works. I've seen that there may be a solder issue on a 13 pin plug but I'm having some difficulty removing the panel to look at it. Apologies if there is already a thread out there for this.

Pete

via control panel removal for Kitchenaid kesc308lss0 range
by babcockpg

Bosch oven meat probe not recognized

The meat probe on my VERY expensive Bosch HIIP054C slide-in induction oven does not register when it's plugged in (usually...there's the odd time where it comes on after being plugged in and the oven has been cooking for a while).
I gather I'll need to test the connectivity of the female socket in the oven, but wonder whether the probe might have gone bad. (I have never put it in the dishwasher or under water).
Any advice on how to get started?

via Bosch oven meat probe not recognized
by Entangler

GE Radiant Electric Cooktop

Hello all-
I have a GE Radiant electric cooktop model number jp3030dj2. two days ago water over flowed on it while boiling and the cooktop shutoff. If the knob is turned on, nothing works. However, as you turn the knob half way from off to on, the power light turns on. Any thoughts will be helpful.

via GE Radiant Electric Cooktop
by slider13

Oven won't heat after refrigerator repair

My gas oven immediately stopped working after I had my refrigerator repaired. The burners still work. I'm wondering if the treasurer'm repairman could have turned off the gas to the oven while fixing the fridge???

via Oven won't heat after refrigerator repair
by MsMertz

Fridgidaire, oven won't ignite, all electronics and top burners work

HI,

My gas range (FPGH3077RF) was installed just 5 weeks ago. The gas Fitter only hooked up my gas lines 3 weeks ago. The oven has worked perfectly. However, the oven was plugged into a 120v wall outlet as I did not have a 240 adapter yet. I finally got the adapter. I pulled the oven out from the wall, plugged in the adapter, plugged the oven into the adapter and pushed the oven back. Now, my bake element will not ignite. The range works, the electronics work, the broiler works. Did I get the one unit out of a million that has a defect and the slightest movement broke the igniter? As far as I can tell there is no pilot or manual way of lighting, its all electronic. Am I mistaken? Any help would be appreciated. Here's the link to the manual: http://manuals.frigidaire.com/prodin...02992502en.pdf

via Fridgidaire, oven won't ignite, all electronics and top burners work
by Brunur