LLVE range wont light

After hooking my range up to a propane cylinder i got a small puff of propane coming out the burners but nothing more. I would light for like 2 sesonds and then go out. I took the regulator off the back and when I turn the propane cylinder on I can hear gas coming through the stove side of the regulator. I've spoke to the manufacturer and the only regulator required is the one on the back of the stove so there is a line running directly from the regulator on the stove to a 100 gallon...

Read more

via LLVE range wont light
by davidrcase

SOLUTION : For issue with Bosch HIIP054C - Induction Range Oven PROBE Issues!!!

To solve the issue :

1. Turn Off the breaker of your Oven
2. Wait 30 minutes
3. Test with : Bake 250
4. Activate on the console the Probe
5. It ask to insert the Probe... SLOWLY insert it until it Recognize it... Do nor insert it fully at first!
6. when the Probe is Detected...
7. Try to insert it fully

It works for me ... may be you can give it a try, know knows, may it could solve your issue!

via SOLUTION : For issue with Bosch HIIP054C - Induction Range Oven PROBE Issues!!!
by regismaltais

1950s Frigidaire Oven door handle help?

Hi!
So we have a lovely 1950s Frigidaire RS50 Stove but yesterday the oven door handle got so loose it fell off. Most unfortunately, you can't access the screw heads from the back of the door. We assume you have to take the door apart in order to access the screw heads, and it being from the 1950s, we assume it also has asbestos and therefore don't want to take it apart for obvious reasons.
the screws are rather short and the handle has a secondary decorative piece that you have to hold...

Read more

via 1950s Frigidaire Oven door handle help?
by Jazzylittledame

ERDS36 Dacor Range Oven Short

I have a Dacor ERDS 36 range and I started the oven and heard a puff.
The clock went out with the display.
This happened before and it was a fried baking element.
Assuming this was the problem, I ordered a new one and went to install and found out the one of the spade connectors had burned off.
The wires are very short and I can't located the burned off wire.
How do you gain access to this.
From the front or the back?

via ERDS36 Dacor Range Oven Short
by webco747

Dacor Range Oven Short

I have a Dacor ERDS 36 range and I started the oven and heard a puff.
The clock went out with the display.
This happened before and it was a fried baking element.
Assuming this was the problem, I ordered a new one and went to install and found out the one of the spade connectors had burned off.
The wires are very short and I can't located the burned off wire.
How do you gain access to this.
From the front or the back?

via Dacor Range Oven Short
by webco747

O'Keefe & Merritt. broiler won't stay lit

Our ancient all-gas early 1950s OKM's broiler won't stay on unless the gas safety button is held in.

The pilot is on, strongly, and the thermocouple is nicely bathed in its flame. If I hold in the safety button for the broiler, it lights right away, but it doesn't stay lit.

I figure it could be the thermocouple at fault, or the safety valve -- anyone know how I can test these?

Thanks!

via O'Keefe & Merritt. broiler won't stay lit
by ningersoll

Oven doesn’t heat to displayed temperature

If I select bake to 400 the thermometer I put inside the oven reads 350....I set it 500 and it’ll read 450

it’s less then 3 years old, does anyone know how to solve this issue?

via Oven doesn’t heat to displayed temperature
by Flipfuzion

VGIC3054BSS Viking Oven will not light

I have a new to me Viking VGIC3054BSS Range and the oven will not light. I replaced the top oven switch / thermostat, the light comes on and there is a click but no ignitors inside working. The top burners are fine......HELP PLEASE!!!!! Mr. Viking Tech.....

via VGIC3054BSS Viking Oven will not light
by studioandolina

Viking Oven will not light

I have a new to me Viking VGIC3054BSS Range and the oven will not light. I replaced the top oven switch / thermostat, the light comes on and there is a click but no ignitors inside working. The top burners are fine......HELP PLEASE!!!!! Mr. Viking Tech.....

via Viking Oven will not light
by studioandolina

non-Zephyr motor to fit Zephyr Venezia ZVE-E30 hood?

My hood blower fan motor is in its last days and I could use some help or advice. Zephyr tells me that my hood, which is labeled "ZVE-E30," actually is a "ZVE-E30S" and its motor no longer is manufactured. Also, they tell me, no other Zephyr motor will work, so I will need to replace the entire hood. This seems a little hard to believe--the hole to the duct is six inches in diameter and the plastic fan/motor housing is roughly nine inches in diameter, which doesn't seem uncommon--but for all...

Read more

via non-Zephyr motor to fit Zephyr Venezia ZVE-E30 hood?
by P-Dub

Bosch Range HDI7152U-01, red light on display

Hello,

I have a BOSCH HDI7152U-01 slide-in duel fuel range. There is a steady red light on the lower left hand corner of the display (see image below). The display panel does not work and the oven will not come on.

I have tried:

1. a full unplug reset for 10 minutes
2. changing the power module (PN...

Read more

via Bosch Range HDI7152U-01, red light on display
by AndrewK2

BOSCH HDI7152U-01, red light on display

Hello,

I have a BOSCH HDI7152U-01 slide-in duel fuel range. There is a steady red light on the lower left hand corner of the display (see image below). The display panel does not work and the oven will not come on.

I have tried:

1. a full unplug reset for 10 minutes
2. changing the power module (PN 00657860) (shown below)

The red light is still on and the display still...

Read more

via BOSCH HDI7152U-01, red light on display
by AndrewK2

Can anyone help with the diagram for Imperial oven model IR-G72-CC?

Hi could you help me with the diagram for an Imperial Commercial Convection oven model IR-G72-CC, serial 11124819, natural gas? I found a supplier for the parts but even they couldn't send me a diagram for some reasons... thank you!

via Can anyone help with the diagram for Imperial oven model IR-G72-CC?
by Bearrepair

F8e0 cooling fan speed low

I am getting the f8e0 error code on my oven. Cooling fan speed low. Quick Google search showed that it could be the fan motor, hall sensor, or board.
Came across a couple of posts here that showed how to check those parts on a different oven. (Fan motor, hall sensor, and board) Is there, by chance, a way anyone can post those same steps?

Thanks

Jon

via F8e0 cooling fan speed low
by Mcnabb75