Jenn Air

After the oven heats up for 8 to 10 minutes i am getting a F3 error code. I replaced the oven Thermostat, but it is still shutting down and giving me the error code.

Is it the mother board?

via Jenn Air
by lombino

NE59J7750WS/AC Samsung Dual Range - Broiler Comes On and Stays on during bake

The broiler element in our Samsung range sometimes comes on and stays on during convection bake in the upper oven. The broiler element stays on and gets very hot even when the oven gets to the set temperature.

Is the broiler element supposed to come on at all during the convection bake setting?

Any idea what would cause this?

I did an error code check and it listed "dC" which is a partition error which refers to the removable partition that divides the oven into two.
Not sure if ths error would be related to the broiler element problem.

Thanks

via NE59J7750WS/AC Samsung Dual Range - Broiler Comes On and Stays on during bake
by jk123

LRE30453ST/01 LG range Oven temperature

So the range will heat to proper temp on convection bake & roast, broiler works, but you set on bake and it to about 25 degrees from desired temp and it shuts down! I'm thinking board replacement?

via LRE30453ST/01 LG range Oven temperature
by mag7762

NY58J9850WS/A Samsung Range Display Problem

I purchased a dual fuel Samsung range (NY58J9850WS/AA) in August of 2016. In October 0f 2018, I lost the fluorescent display after an oven cleaning cycle. I have tried three replacement display assembly modules (DE96-01050B) in the range with all exhibiting the same strange behavior. In all instances the touch pads are mapped in an upside down arrangement. For example, a press of the “1” pad results in a display of “8”, a press of “8” results in a display of “1”.

To initiate a setting of the clock, a press at the bottom of the display is required even though the clock pad is at the top of the display. My original board works perfectly in regard to mapping of touch pads.

Two assemblies were purchased at Sears Parts Direct and one from Appliance Parts Pros. It is apparent that the firmware controlling the mapping of touch pads is wrong.

Can anyone please help me resolve this issue?

via NY58J9850WS/A Samsung Range Display Problem
by ken-jacobs

Lg range

So the range will heat to proper temp on convection bake & roast, broiler works, but you set on bake and it to about 25 degrees from desired temp and it shuts down! I'm thinking board replacement?

via Lg range
by mag7762

Samsung Dual Range - Broiler Comes On and Stays on during bake

The broiler element in our Samsung range sometimes comes on and stays on during convection bake in the upper oven. The broiler element stays on and gets very hot even when the oven gets to the set temperature.

Is the broiler element supposed to come on at all during the convection bake setting?

Any idea what would cause this?

I did an error code check and it listed "dC" which is a partition error which refers to the removable partition that divides the oven into two.
Not sure if ths error would be related to the broiler element problem.

Thanks

via Samsung Dual Range - Broiler Comes On and Stays on during bake
by jk123

LRE30453ST/01 LG Range Burner won't turn off

The front left burner will not turn off. The display shows HS for hot surface. I can manipulate the controls and get the burner to go off but it comes back on in less than 15 seconds.

via LRE30453ST/01 LG Range Burner won't turn off
by grandbea

LG Range Burner won't turn off

The front left burner will not turn off. The display shows HS for hot surface. I can manipulate the controls and get the burner to go off but it comes back on in less than 15 seconds.

via LG Range Burner won't turn off
by grandbea

WS..DS7W0 Oven element substitution

HELLO and Help
This 30+year old 27 inch wall oven (with broil and rotisserie) was manufactured for the Canadian Department Store Chain, Eaton's, by whom I don't know.
Model WS..DS7W0 Serial # 202923 KW3.8 Max. line current 19.0 amps.
The current bake element has expired. It was a generic replacement for the original and installed 5 years ago by a technician. There is no indication of wattage.
Question: What happens if I install a higher wattage element? For example, I install a 3000 watt in place of a 2500 watt????
This is urgent, the spouse is getting worried about not having an oven for Christmas Eve. Help!!!

via WS..DS7W0 Oven element substitution
by rentltd

Frigidaire Gas Range Light switch

Hello,

Yesterday my wife turned on the oven light using while baking something and was unable to turn it off. When pushing the switch in the control panel it beeps but the light stays on. All the other buttons do what they are suppose to do.

I've turning off the power for a couple of minutes (turned off the circuit breaker) after turning it back on the light is still on.

Thanks,

AJ

via Frigidaire Gas Range Light switch
by aja1216

oven element substitution

HELLO and Help
This 30+year old 27 inch wall oven (with broil and rotisserie) was manufactured for the Canadian Department Store Chain, Eaton's, by whom I don't know.
Model WS..DS7W0 Serial # 202923 KW3.8 Max. line current 19.0 amps.
The current bake element has expired. It was a generic replacement for the original and installed 5 years ago by a technician. There is no indication of wattage.
Question: What happens if I install a higher wattage element? For example, I install a 3000 watt in place of a 2500 watt????
This is urgent, the spouse is getting worried about not having an oven for Christmas Eve. Help!!!

via oven element substitution
by rentltd

Samsung NX58K9850SS/AA Flex Duo Touch Screen Issues

So I bought this oven from a liquidation website with the knowledge that it would take some repair. Mostly it was just missing some parts and had a couple of dents. It was apparently a floor model at a Best Buy somewhere. So as far as I can tell it has never actually been installed in a home.

Anyways when I got it and started to work on it right away the control panel wasn't working. All display section light up but no no response. So I pulled the display assembly module and noticed one of the wire connectors was almost somepletly pulled off the board. So I assumed that had to be the issue and ordered the replacement. https://www.appliancepartspros.com/samsung-assy-module-assy-de92-03967a-ap6002980.html

Once I got it installed it did the exact same thing. Began to trouble shoot more and discovered a set of wire connectors that went in the the PCB was not connected. Plugged it in and the display board light up correctly and you hear the chime it makes. Felt like an idiot and plugged the old display board back in and it worked just like the new one ��. But that connector actually came completely off so it needed replaced anyways.

But now the touch is all off. only a couple buttons respond but none of them respond to the correct setting. Button 1 puts up number 7 and number 2 puts up 8. Did the same on the old display module. So I thought I was ordering the Digitizer Glass part but I ordered the wrong part ��. I couldn't find the digitizer listed in the parts list at all not on any other site either. So I thought maybe it's the main board PCB.

Ordered that https://www.appliancepartspros.com/samsung-assy-pcb-main-de92-03960d-ap6002976.html. And installed it and guess what......exact same issue.

So the only thing I can think of is the glass digitizer but I cannot find a MFG Part number for that piece.

Someone help please!!!!!!

via Samsung NX58K9850SS/AA Flex Duo Touch Screen Issues
by WHEELERMEISTER

NX58H9950WS Samsung Range E-2C error code

Display shows E-2C error code and time.
Visible "Off/Clear" as well. After pressing "Off/Clear" I can hear cooling fan starting which after few seconds shuts off and display goes back to E-2C error.

via NX58H9950WS Samsung Range E-2C error code
by Janek18

Samsung NX58k9850SS Flex Duo Touch Screen Issues

So I bought this oven from a liquidation website with he knowledge that it would take some repair. Mostly it was just missing some parts and had a couple of dents. It was apparently a floor model at a Best Buy somewhere. So as far as I can tell it has never actually been installed in a home.

Anyways when I got it and started to work on it right away the control panne wasn't working. All display section light up but no no response. So I pulled the display assembly module and noticed one of the wire connectors was almost somepletly pulled off the board. So I assumed that had to be the issue and ordered the replacement. https://www.appliancepartspros.com/s...ap6002980.html

Once I got it installed it did the exact same thing. Began to trouble shoot more and discovered a set of wire connectors that went in the the PCB was not connected. Plugged it in and the display board light up correctly and you hear the chime it makes. Felt like an idiot and plugged the old display board back in and it worked just like the new one 😭. But that connector actually came completely off so it needed replaced anyways.

But now the touch is all off. only a couple buttons respond but none of them respond to the correct setting. Button 1 puts up number 7 and number 2 puts up 8. Did the same on the old display module. So I thought I was ordering the Digitizer Glass part but I ordered the wrong part 😭. I couldn't find the digitizer listed in the parts list at all not on any other site either. So I thought maybe it's the main board PCB.

Ordered that https://www.appliancepartspros.com/s...ap6002976.html. And installed it and guess what......exact same issue.

So the only thing I can think of is the glass digitizer but I cannot find a MFG Part number for that piece.

Someone help please!!!!!!

via Samsung NX58k9850SS Flex Duo Touch Screen Issues
by WHEELERMEISTER

Fan cycles on/off, is noisy & heat is uneven

We just bought the house so I don't know the history.
The fan is quite noisy and seems to turn on/off constantly??

The fan cycles on/off about every 20 seconds only in convect mode so I'm suspecting the convection fan?

via Fan cycles on/off, is noisy & heat is uneven
by larkamr@aesecurity.ca

E-2C error

Display shows E-2C error code and time.
Visible "Off/Clear" as well. After pressing "Off/Clear" I can hear cooling fan starting which after few seconds shuts off and display goes back to E-2C error.

via E-2C error
by Janek18

Kitchenaid Double Wall Ovens/Electrical smell/buzzing sound/F9E0 error

Error code: F9E0 ("Product not wired correctly")

Electric Burning odor, then loud "buzzing/whirring" sound when CANCEL to shut off.

Kitchenaid Double 30" wall ovens, model KODE307ESS00
Installed/New about 3 years ago


Ok, so my wife's doing Christmas baking and had the top oven on for about 4 hours. She called me into the kitchen and said she smelled an electrical odor. I could barely smell it, but told her to turn the oven off (CANCEL on the upper oven) as I ran to the cellar to throw the break off on my subpanel. As I was going down, she said she hear a loud "buzzing/whirring" sound that she claimed wasn't the fan.

Next, I inspected all cabling... behind the cabinet drawer under the ovens and in the cellar coming out of the subpanel. All cables looked normal and felt cool to the touch. Their was no sign of them having been overloaded.

I then turned the breaker back on and tried to set the top oven to 350F... and got the F9E0 error code. It was the same when I tried the lower oven... so whatever the problem is, it is affecting both ovens. (So... NOT either of the control boards?) I tried this a few times--same error.

I then shut off the breaker for safety.

I should say that I've been doing my own electrical work for over 40 years... this was a neat, clean install. Large junction box installed behind the oven... large wire nuts used to make connections (very tight)... cables secured all throughout the run.


All the electronics in this model are above the top oven and it seems that any repairs must be done by uninstalling the ovens from the cabinet. Which is my hellish problem... it's installed about 2" from a wall and window with a radiator under the window that is about 6" taller than the bottom of the lower oven. What a pain this will be for a repairman!

Advice... any ideas on what component it could be?


New info:

The oven's breaker has been shut for over an hour...

I just turned on the breaker again so I could run the diagnostics (CANCEL+CANCEL=START) to see if there were any other error codes in its memory that we missed previously (there aren't). I then turned on the upper oven to 350F and to my surprise the error didn't show up... it continued to preheat for a couple of minutes. I tried the same on the lower oven--no error.

Could it be that the thermal fuse might have somehow melted and caused a short which might have caused the F9E0 error? (If so, this would be a simpler repair since I'd only have to slide the unit out a few inches to get to it. (I'm hoping for something simple, I know!)

Still, I'm not going to use it until I know for certain it's safe.

via Kitchenaid Double Wall Ovens/Electrical smell/buzzing sound/F9E0 error
by finzidad

best oven under $1500

I don't know if this is the best place to look- but I am wondering if there are any recommendations on which brand would be the best to go with for under $1500?

I suppose I could go to consumers reports but it seems like they don't cover all the brands- and the brands they do cover, the models are never available.

anyway- I just don't want to end up with another bummer oven like my 20 year old Maytag Gemini.

Thanks,

Joey D.

via best oven under $1500
by California Joseph

VGIC3666BSS Viking oven igniter replaced, continues to not stay lit

So, I have here a VGIC3666BSS, date of manuf. 031308. The problem is that the oven igniter works but the oven will not stay lit. I have a short video if I can post I will. I have already replaced the single igniter (U shaped burner tube), and it will light for about 3 seconds then I hear a clicking sound and the gas stops flowing completely and the oven flame stops. I read about an oven safety valve in another thread. Sounds like that may be it though I don’t know the PN for that. Help.

via VGIC3666BSS Viking oven igniter replaced, continues to not stay lit
by Jackson Wallace

Thermador range model PRG364GDUS front left burners (XLO) don't work

I have a circa 1999 Thermador range model PRG364GDUS serial number #99070026F and the problem is that the front left burner stopped working about a month ago (it is one of two “XLO” (extra low) burners on the unit). The other three burners, the griddle, and the oven work just fine. We did have a problem a few years ago where the igniters would stay on from 2-20 seconds after the burner lit however that problem just went away with time.

I wanted to order a new “potentiometer” for that burner however first I needed to know what version of the simmer control unit I had so I popped off the kick plate and started to dust off the simmer control so I could read the numbers. That is when all four igniters started clicking. Now I know a little bit about electronics and I am pretty good with a soldering iron however I am not expert by any means and do not know how to use an oscilloscope. I have done some thru-hole repairs on old solid state and tube stereos.

So I was a little surprised when the igniters started clicking when all I did was gently touch the simmer control unit to wipe off the dust. Yes I did not unplug the unit, and to get the igniters to stop clicking I had to unplug it. Then every time I plug the unit back in I get two clicks on the igniters (not sure if this is normal or not). So to me it seems like there is something wrong with the simmer control and so I am asking for advice on what might be wrong and how to fix it. Here are my thoughts on it and I would welcome opinions from the Forum:

bad connection
to try and fix remove all the wires, clean them off, clean the connection contacts, reseat
bad solder joint
reflow solder joints
bad board (send in for repair?)
bad part on the board (which part might be bad? I could repair it myself)
faulty wiring
break out the DMM and test for continuity etc. Not really sure where to start but I’m willing to learn…


This is what I have tried so far (all this before I tried to dust off the simmer control unit).

I pulled the unit out, unplugged, turned off the gas.
I swapped the potentiometer from the left front burner with the left rear (working) burner and tested it and it worked. However, after putting the unit back together, when I plugged it in, I get two clicks on the igniters and the left front burner does not work anymore. However, when I was dusting off the simmer control and the igniters kept clicking, I tried the left front and it worked again. However, once I unplugged the unit, plugged it back in (two clicks), the left front does not work again.

The “bad” potentiometer that used to be on the left front that I removed from the unit has an obvious trace that is burned out - the connection closest to the edge of the board. So something fried the connection or the pot just went bad and fried itself I don’t know I have not taken it apart yet to see what its made out of.

So this is what I think so far: I think that the simmer control is having some problems. Now whether that can be fixed simply by reflowing the solder or cleaning off the connections I don’t know. I may need a diode, resistor, or capacitor replaced - I have not taken it out of the unit to see what’s it made out of however its 20 years old and the electrolytic capacitors are at the end of their life and of course the environment it is in is hard on the board as well. The board could need a full rework.

I think the bad pot on the front left burner is shot and I need to get a new one. I ordered one (part #422748) to see if that will at least work if the simmer control is behaving.

OK I’m done and thank you for reading along. Let me know what you think and what your recommendations are.

Best wishes,
Michael

PS: The simmer control says model SQ003 with no “-H” after it so I am not sure if it is a 422882 or the “old” 411441. I ordered a pot replacement #422748.

via Thermador range model PRG364GDUS front left burners (XLO) don't work
by mjgillen

Viking oven igniter replaced, continues to not stay lit

So, I have here a VGIC3666BSS, date of manuf. 031308. The problem is that the oven igniter works but the oven will not stay lit. I have a short video if I can post I will. I have already replaced the single igniter (U shaped burner tube), and it will light for about 3 seconds then I hear a clicking sound and the gas stops flowing completely and the oven flame stops. I read about an oven safety valve in another thread. Sounds like that may be it though I don’t know the PN for that. Help.

via Viking oven igniter replaced, continues to not stay lit
by Jackson Wallace

Fivestar has oven issues

First post...Having issues with a Fivestar four burner gas oven/range. Basic problem is: When oven is plugged in, oven light comes on (even when oven dial not turned on), indicating the oven is heating but it is not. When the problem was first noticed, the oven burner was coming on and remaining on (almost as if it was stuck) but now it is not. Currently, when plugged in, the glow bar is glowing. Gas is getting to the unit as the stovetop burners will ignite manually but cannot use oven/broiler.

Made a general service call and after ten minutes given a $700 quote to replace thermostat and safety valve. I’ve replaced the glow bar before but thinking that isn’t the issue. I’d appreciate the board’s thoughts and suggestions. The knowledge base here is amazing.

via Fivestar has oven issues
by Felix29

VSG3054BDBK Factory Viking igniter vs generic

My Viking 30” gas range broiler igniter needs to be replaced. The factory part (Pb040001) costs over $200.
The same part on eBay or Amazon is about $20. Is there really a different in quality? Thank you!

via VSG3054BDBK Factory Viking igniter vs generic
by Flopsycat

Factory Viking igniter vs generic

My Viking 30” gas range broiler igniter needs to be replaced. The factory part (Pb040001) costs over $200.
The same part on eBay or Amazon is about $20. Is there really a different in quality? Thank you!

via Factory Viking igniter vs generic
by Flopsycat

Samsung Double Oven NE59J7850WG/AA - Broiler won't turn off

So we've had the Samsung oven for a year-and-a-half. Today I cooked a pizza in within 8 minutes I had a kitchen full of smoke. Come to find out the broiler was on. I thought it was my fault so I cooked another Pizza using the bake function in quickly realized the broiler was coming on. No matter if I use the top or bottom of the oven using the bake function the broiler always comes on. I've tried resetting the circuit breaker and that didn't help. After calling Samsung they said my unit was out of warranty. But after reading the manual it stated that the radiant heater had a five-year warranty. Does anybody have any suggestions?

via Samsung Double Oven NE59J7850WG/AA - Broiler won't turn off
by Venom93corba

Help my GE model # jgsp42set1ss control panel is dead

Help I tried to reset the breaker that didn’t work I have the Control panel exposed I thought I could find someone who had a similar problem n I cannot find any site with my model I need someone to tell me what to check with my voltage meter to determine if it has power at all or if I need a whole board plz help

via Help my GE model # jgsp42set1ss control panel is dead
by Noel