Thermador Range PG364GLBS/03 not igniting or clicking

I have a 17 year old Thermador still in good condition. For several years it was harder to get the pilot on the range to light. The board was just changed to the universal because the oven would high up over 250 degrees and now the oven is working fine. Then now none of the ranges ignite. I had 2 tech look at the issue for the ignitor both side I need to replace the spark re-igniter BSH 00189010 but it's hard to get.

One tech tested the voltage output from each and it's getting current...

Read more

via Thermador Range PG364GLBS/03 not igniting or clicking
by anthonys650

X304GGVX Bertazzoni Range Oven Door problem .

Hi, I have a 30" Range and recently have a problem with the oven door. When I close the oven door, the door shifts down( drops down) and makes a loud sound. It happens every time that I open and close the oven door. Anybody can help me with this issue? Thanks

via X304GGVX Bertazzoni Range Oven Door problem .
by alirezamaryam

Bosch HGS7282UC/06 Oven Control Board Configuration Instructions

Can anyone point me to where I can find the TSB for a Bosch HGS7282UC/06 Oven Control Board (Display Module) Configuration Instructions please?

Or, if you have replaced this board, could you upload images of the instruction pages please.

Thank you in advance!

via Bosch HGS7282UC/06 Oven Control Board Configuration Instructions
by djcz

What is the white paste where the coil touches the cooktop in an induction cooktop

Can someone tell me what the white paste is, where the coil touches the cooktop in an induction cooktop and what purpose does it serve?. This is a general question since the cooktops I have taken apart are similar. I'm curious as to if it is a vibration damper and may reduce a buzz that often occurs during operation. Thanks

via What is the white paste where the coil touches the cooktop in an induction cooktop
by EmAre

Bosch PKN645E01/01 stovetop, single plate sometimes stops heating on low temperatures

Hi,

I have the following problem that is a bit particular:

The large circular dual ring plate sometimes (most of the time actually) stops heating about 10-30 seconds after initially turning it on. No error, simply stops heating. Turning it off&on again typically resolves the issue and I can cook without further issues. Sometimes this requires turning it off&on again 1 or 2 times more (again within less that 10-30 seconds).
This is only ever an issue at the start, if it has been on for > 2...

Read more

via Bosch PKN645E01/01 stovetop, single plate sometimes stops heating on low temperatures
by PeterM

GE Wall Oven JRP15WW3WW

Greetings,

I am helping my neighbor repair her GE JRP15WW3WW wall oven. It was manufactured in 1998, and from what my neighbor tells me, it probably hasn't worked for the past decade, possibly longer. She indicated that the oven started throwing multiple error codes after she used the self-cleaning feature, but she doesn't remember what the codes were.

My initial research on the JRP15 series of ovens made me aware that there are several design issues with this oven that make it prone to...

Read more

via GE Wall Oven JRP15WW3WW
by pqcracker

Thermador SEC301BB/03 Squeaky hinges and door won't close

Squeaky hinges and door won't close. The OEM part is nla. However, even though most sites say it's a Bosch part, I know it is not.
Nuova Star SPA, Italy. 900001143, but I'm looking for the part equal on the Whirlpool parts site and can't find a cross ref.
The Bosch "OEM" part number is 00425990.
Anyone have an idea?

via Thermador SEC301BB/03 Squeaky hinges and door won't close
by fritz

Gas to induction and wiring

We want to convert our gas cooktop to induction. It's currently mounted above a gas oven. The gas stove is 120V but almost all induction cooktops are 240V. The current gas oven is 240V. Question is...with 240V already running to behind the oven (but the current stove plugged into 120V), will we need to run another line from the breaker box to get 240V for the new stove, or is the current oven line sufficient for both? I can't pull out the stove or oven (well, I fear causing a gas leak if I...

Read more

via Gas to induction and wiring
by flyfresno

Viking Broiler/Oven Lights and Goes Out Immediately

I purchased a Viking DCCG130 secondhand. It sat unused for approximately 6 months before installing it. The range works fine but the infrared broiler and oven have never worked. They each light with plenty of flame, but are extinguished within 3 seconds. Is this a fault of some type of flame sensor or thermocouples-type thing?

via Viking Broiler/Oven Lights and Goes Out Immediately
by WhyWontThisWork

Bosch Microwave HMC80252UC/01 - no power no lights but not blowing breaker

I have ordered the door switch kit as I want those on hand but could that be the problem given that there is no power at all to the front panel and oven light? I have reset the breaker but it seems fine.

via Bosch Microwave HMC80252UC/01 - no power no lights but not blowing breaker
by pogosenior

I’m looking for a range cooker buying guide.

I’m hoping to find a range cooker buying guide here as we are looking to update our kitchen. Does anybody have something that would help please?

via I’m looking for a range cooker buying guide.
by robmeercat

Dacor Double Oven Overheating - With great video and sound!!

Hey everyone,
My older house came with a Dacor double oven and has been working great for years. I also cant find the model number anywhere. Today we were using both the upper and lower ovens at the same time when the upper oven started making these sounds (PLEASE WATCH AND LISTEN TO VIDEO)... the control board was beeping with the error message and something else was making a grinding sound in the upper oven. The display read "L20 OVER TEMP" at the time. I was able to find a manual...

Read more

via Dacor Double Oven Overheating - With great video and sound!!
by gizmoduck

Looking for Thermador cit36xkbb service manual

Hello,

I got a Thermador cit36xkbb from a customer that had it attempted repair by another service company. There are 48 induction coils so I am looking for the service manual and connectivity diagram to make sure it has been re-assembled correctly before starting to test the boards. Anyone can find that service manual? I have been searching and did not find anything.

Thanks!
Fred

via Looking for Thermador cit36xkbb service manual
by fred eric

Low broiler setting only works sometimes

I have a new Frigidaire electric range. Model number FFEF3016VB. The broiler works on high but not on low, occasionally it will work on low but most often it will not.

via Low broiler setting only works sometimes
by shelly23

Dacor ECS130 Wall Oven Not Heating Up - trying to troubleshoot

Oven has been slow to heat up and would not reach temp for last few weeks - now there is no heat from either bake or broil elements.
I tried resetting the unit on the device with red button behind control panel and that did not help.

I checked the temperature sensor at room temp and resistance measured right at 1100ohm, so from what I read that is good. The
control panel and display work fine, the fan comes on, but the elements don't heat up at all (I can touch and they are cool).

It...

Read more

via Dacor ECS130 Wall Oven Not Heating Up - trying to troubleshoot
by JB1993

Dacor Gas Burner Base Seized Up

I am looking for advice on how to remove one of the burner bases on my Dacor gas cooktop. The ignitor needs to be changed on this particular burner, but the technician said that over time the heat from using the burner has made it impossible to remove, due to seizing up. The ignitor can not be changed without removing the burner base according to the technician.

I have applied some SeaFoam Deep Creep penetrating lubricant and let it sit for 48 hours, but the burner rings, which hold the...

Read more

via Dacor Gas Burner Base Seized Up
by CBL

Whirlpool Oven buttons not working gw397lxus06

Whirlpool GW397LXUS06 Accubake oven - started with some buttons not working- had a repair guy come out and said control panel needed replaced and gave me a very high quote. I bought a new control panel but had simular issues - all buttons are not working. I figured the only other thing it could be is the membrane with the ribbon wires and the buttons. I ordered a new one, installed it, same results - although there is so.e button action. If I hold the bake button down it goes to set...

Read more

via Whirlpool Oven buttons not working gw397lxus06
by milzticket

VIKING VGIC365-4QSS Burner Ignition Issues

Hello! I would be grateful for any assistance.

I have a VIKING VGIC365-4QSS, serial number R06150113261. It was made in June, 2001. Most of the parts are original.

I'm having a problem with the RANGE (oven is fine). Over the last few months, the burners have gradually not been lighting well. Only 2 burners out of 5 are sparking regularly. I replaced both spark modules, the one that lights the left 2 burners, and the one that lights the right two burners and the grill.

At first, I...

Read more

via VIKING VGIC365-4QSS Burner Ignition Issues
by kbleau

Bosch double wall oven HBL8650UC/10 serial 920500053 will not let me to bake or use the broil feature.

This double wall oven comes up with set the clock, after setting the clock it will go back to the same "Info" mode and will not let me to bake or use the broil feature. Even unplugging it didn't work. Bosch technical support will not help. Could someone tell me if it's the display board or the touch screen faulty.

via Bosch double wall oven HBL8650UC/10 serial 920500053 will not let me to bake or use the broil feature.
by Seap1970

HE Café Induction CCHS950P2M4S1 Range does not work

About every month, the range stops working. When I turn the knobs, the light around the knob does not come on, and the induction element does not start. After about a week, it starts working again. I bought it 11 months ago, and is still under warranty. However, they've been out twice and have no idea what is wrong as it returned to normal function by the time the tech shows up.

The oven continues to work throughout.

Anyone else have this issue?

via HE Café Induction CCHS950P2M4S1 Range does not work
by blackcat

Where to find a WB24X5285 replacement thermostat for our GE J ASO3 R3 oven ...

Hi, all!

We have in a vacation cabin a 20+ year-old little GE J ASO3 R3 range whose thermostat appears to be dying or dead. At first the oven simply ran a pretty constant hot, but now it appears to go up and down, requiring pretty constant watching to cook anything effectively. Unfortunately, the WB24X5285 thermostat I think I've found in the GE diagram has been discontinued ... and nobody lists a replacement! Uh oh.

We'd love to not have to go and find another tiny unit like...

Read more

via Where to find a WB24X5285 replacement thermostat for our GE J ASO3 R3 oven ...
by davidtg

Can a tech recommend a reliable well built propane gas range for me?

I have an older model GE Gas Range JGBP26GEJ4AD from the eighties which is well made and has been incredibly reliable. My wife wants a new stove and despite my trying to convince her that none of them are as well made she insists.

Having serviced them can one of you recommend a reasonably well made brand (or model) that won't have obsolete parts in four years? I know the electronic controls seem to be the most trouble prone parts on the newer ones besides the thinner metal so any type...

Read more

via Can a tech recommend a reliable well built propane gas range for me?
by craftech

Wolf DF304 NG to LP

Hi I have a 30in Wolf DF304 I'm looking to convert from NG to LP. Wolf tells me due to its age its a "liability" and will not sell me a conversion. I've done some research, it seems simple enough to convert the regulator to LP. My question is of anybody could lead me in the correct direction for orifice sizing. Any help would be greatly appreciated!

via Wolf DF304 NG to LP
by mlen

Wedgewood stove - oven wont heat, no gas hissing sound, pilot is lit, burners still work.

I have an old wedgewood stove, and used the oven and broiler fine the other day.
Afterwards the house smelled strongly of gas so I aired it out and relit the pilot which had gone out.
The pilot is still lit, but now when I try to bake the oven and broiler won't get hot. There is no sound of hissing gas like usual.
Anyone have any idea what's going?
The pilot is lit, I can't find any emergency cut off buttons or switches anywhere ( I have not pulled it away from the wall), and the burners...

Read more

via Wedgewood stove - oven wont heat, no gas hissing sound, pilot is lit, burners still work.
by Miss F

WS..DS7W0 Oven element substitution

HELLO and Help
This 30+year old 27 inch wall oven (with broil and rotisserie) was manufactured for the Canadian Department Store Chain, Eaton's, by whom I don't know.
Model WS..DS7W0 Serial # 202923 KW3.8 Max. line current 19.0 amps.
The current bake element has expired. It was a generic replacement for the original and installed 5 years ago by a technician. There is no indication of wattage.
Question: What happens if I install a higher wattage element? For example, I...

Read more

via WS..DS7W0 Oven element substitution
by rentltd

LP to NG Conversion Wolf Gourmet AS30KI-4 (1999)

Good Day,

Purchased a pre-owned 30" Wolf Gourmet AS30KI-4 range. This was manufactured in October 1999 about six months before Sub Zero bought the brand. Looks to be in nice condition and seller stated such. Just picked up so have not even had a chance to plug in, still sitting in van. If its weight is an indication of the quality then this is a fantastic range.
It is currently set up for LP, I need to convert it to natural gas. Purchased the conversion kit through Dvorsons for...

Read more

via LP to NG Conversion Wolf Gourmet AS30KI-4 (1999)
by CJerome

2002 Viking VDSC4856QSS broken wire behind back wall...now what?!!

Hi! My 2002 Viking VDSC4856QSS lower baking element popped. When I went to remove the broken element, one wire broke off behind back wall...now what?!! Any ideas? There doesn't seem to be any way to open / remove the back wall. Can I go in from the top, or do I need to go in through the back? Are there service manuals available anywhere? Thanks!

via 2002 Viking VDSC4856QSS broken wire behind back wall...now what?!!
by CPNYRickD

Bertazzoni X304GGVX Oven takes forever to heat

I have a Bertazzoni X304GGVX hooked up to propane that takes over an hour to preheat to 400 degrees F, if ever, I usually just cook longer or use the grill.
It starts fine just won't heat. I've ordered a new thermocouple as I've read on other boards that they have a tendency to fail and could be the culprit for many issues, although I haven't been able to find anyone with my model and setup. I've been told that it shouldn't have anything to do with being hooked up to propane. Our top...

Read more

via Bertazzoni X304GGVX Oven takes forever to heat
by Peeroos

Whirlpool Gas range, oven intermittently will ignite, but not reignite after reaching temp, WEG760H0DS0

Hello,

So my whirlpool oven has not been working normally for the past 6-9 months. The oven would ignite like normal, would pre-heat to temp, then would not keep temp. (I used a thermostat/thermometer in it it to check this) I would turn it off for 15 -30 secs, hit bake again and set temp then start and it would heat back up normally and work like normal. Now over the last month it wont even ignite most of the time. I will have to retry several times before it finally ignites, it would...

Read more

via Whirlpool Gas range, oven intermittently will ignite, but not reignite after reaching temp, WEG760H0DS0
by TMAN_21

Broan Range Hood Evolution 3 QP3 Series - Fan does not want to turn off

So how about Range Hoods? I have a Broan Evolution 3 series range hood my wife is convinced that it is possessed. However, I don't find an area for range hoods or range hood problems--not under stoves/ranges, or HVAC.

If a mod could point me to the right sub-forum, I'll describe the issues and ask for help on this.

QP330SS is full model number, just found it.......

via Broan Range Hood Evolution 3 QP3 Series - Fan does not want to turn off
by Opihi59

Looking for a propane conversion kit for a Viking VGSC305-4BDSS

I purchased this range from a seller who said it was propane but it is nat gas.
It is an older model and I am having trouble finding the conversion kit for it online.
I'd really appreciate it if anyone know where to find it.
Thanks!

via Looking for a propane conversion kit for a Viking VGSC305-4BDSS
by yopro15

Bosch Gas stove series 500 burner not working

Hello

I have Bosch gas range stove. I believe it is the series 500 model. The front right burner stopped working. I do not hear the clicking when turning it on but I do smell the gas and when i light it with a lighter it works. The rest of the other burners are working fine. Does this have to do with the spark module that needs to be replaced?

If so wondering how difficult the install is

Thanks

via Bosch Gas stove series 500 burner not working
by Arcadian9

VDSC4854G0SS Viking Oven selector switch replacement

Viking Professional Dual Fuel Oven Replacement Switch. Finally scored a replacement selector switch PJ030001 (discontinued). 8 position switch. Any advice, cautions, suggestions. Looks like it should be pretty straight forward. Appreciate it, John VDSC4854G0SS

via VDSC4854G0SS Viking Oven selector switch replacement
by JohnMason8525

Viking VGSC 306 oven bottom removal

My oven seems to not be heating properly. Is there a trick to removing the oven bottom panel to inspect the igniters etc? For this convection oven the bottom panel appears to require the convection fan cover to be removed to then push the bottom panel back far enough to then tilt/lift out. I can easily remove the top 3 hex screws on the fan cover, but the bottom two hex screws are obscured by the back edge of the oven bottom(?). I have attached a photo with the fan cover edged up as far as I...

Read more

via Viking VGSC 306 oven bottom removal
by JSS

LDE4413ST- Ultra heat only works on levels 1 to 8

Good day everyone, I have issues with the UltraHeat of the front burner of our LG LDE4413ST Range. The UltraHeat (outside heating element) works fine from level 2 to 8, once the knob is moved to level 10, the outside element shuts off and only the inner element remains on.

Tech guy said it was either the control board or a connection under the element. But no clue. Any one has suggestions? Thanks!

via LDE4413ST- Ultra heat only works on levels 1 to 8
by txmalsb

Convection element not working in LG LRE3083ST

Convection element never activates in either Convection Bake or Roast mode. I am able to activate the element using the LG diagnostic utility so I know that the relay and element are ok.

The convection fan and both the bake and broil elements do activate in both convection modes.

Any thoughts are appreciated.

via Convection element not working in LG LRE3083ST
by adolimpio

Help repairing or finding replacement parts for a Unique (brand name) model UGP-30EOF1 over/range.

I own a Unique model UGP-30EOF1 oven/range. One of my burners on the range will not remain lit. I've replaced the thermocouple twice. And on the present thermocouple, I verified that it was putting out about 350 millivolts before I installed it, as recommended by the manufacturer. The burner flows gas great as long as you push in the valve. About 1 time out of 20, it'll stay lit on its own, but the other 19 times you're out of luck.

Now the manufacturer says I need to replace...

Read more

via Help repairing or finding replacement parts for a Unique (brand name) model UGP-30EOF1 over/range.
by txgp17

JENNAIR JES9800 CONTROL BOARD

Hi,
I just purchased a service manual for the range and it is from year 2006. My range was purchased in 2010. Is there a new version of the service manual? I am on my 3rd control board with first one replaced under warranty and would like to know what is the latest control board EOC-II or EOC -III nd the associated software version? My new control board shows no error codes and all panel buttons work, but the issue I am having is that the bake temperature is about 40F lower then it should...

Read more

via JENNAIR JES9800 CONTROL BOARD
by marty100

NXR Model #NK3611 won't ignite

Hi there. NXR Model #NK3611 won't ignite. Cleaned all areas and debris, cleaned surfaces and holes. Hear a few clicks then nothing but a gas smell. I did see a few glimmers of light but it never caught. All 5 other burners work fine. The one that doesn't work now is the one I use daily. Any ideas?

via NXR Model #NK3611 won't ignite
by lisasum

samsung nx58m9420ss/aa stove/oven gas valve question

This gas oven/range unit; the ovens bake not working. Igniter is in good condition. I have continuity across both bake and broil valve prong pairs and 120V across wire leads feeding both gas valves according what is turned on . Valve is listed for 3.03/3.3 vac ?? Can gas valve be defective even when have continuity across gas valve contacts ? Is the safety work from a photocell or continuity of a good igniter ? Could gas valve be defective even though there's continuity in coil of valve ...

Read more

via samsung nx58m9420ss/aa stove/oven gas valve question
by howie333

Avanti 20" electric range indicator light stays on dimly.

Bought a new Avanti 20" electric range for our small airbnb apartment. Indicator light for stove top burners stays on dimly all the time. Surface burners are not hot so I'm thinking it's more of a nuisance than a safety issue but since it's in an airbnb unit, we keep getting calls from our renters that they are concerned that it is a safety problem. When a burner is turned on, light goes full bright, so normal in that sense. It's a small neon, (I think), 220v light bulb. Avanti...

Read more

via Avanti 20" electric range indicator light stays on dimly.
by tomski71

Bertazzoni PROF366DFSXT Range Temperature too high

Hi

Bertazzoni PROF366DFSXT 2.5 years old.

Consistently running a high temperature. Both temp sensor probe and thermostat have been replaced

If you set to 350, the "dial" gauge showing the temp climbs to 350 then stops, but the oven continues heating to about 410 (confirmed with oven thermometer). If you adjust the temp higher the dial gauge jumps up to the actual temp the oven is at. Any help appreciated!

Thanks

Jake

via Bertazzoni PROF366DFSXT Range Temperature too high
by syncroand101

GE Double Oven Model #J780T3YE Serial #ZT010132F

Looking for information on GE Double Oven Model #J780T3YE Serial #ZT010132F trying to find hinge replacement for top oven.

via GE Double Oven Model #J780T3YE Serial #ZT010132F
by NeedHelp55

HBL5650UC/03 Bosch oven persistent resetting

Howdy Folks,
My Bosch HBL5650 oven is continually resetting bringing it into clock settings which must be configured for use. The oven is unusable. I found a similar thread

FIXED - HBL8650UC/10 Bosch double oven display keeps resetting

Our Bosch double oven display board keeps resetting and at first it would only happen once in a while but now it is happening all the time and it’s won’t let us cook. I’ve noticed that it also happens when you touch the “info” button. I have shut off the breaker for 30 mins in hopes it would...

www.applianceblog.com

The remedy on that thread recommended a replacement of the main control board. I replaced the control board twice now as I though perhaps my initial change was a bad board. (Bosch part number...

Read more

via HBL5650UC/03 Bosch oven persistent resetting
by DIYGuy88

All burners take very long to light even manually

My tenants told me that all 4 burners on the stove take a long time to light (30-60 seconds). This is the case both using the stove ignition and when using a lighter. The issue has been getting worse and it affects the burners they never use. There is no smell of gas while waiting for the burner to light. Oven works fine. Any ideas?

via All burners take very long to light even manually
by pdooley

Bosch HBL3350UC/09 oven says it’s preheated 75 degrees or more before it is

Hi all-

Back again. My Bosch wall oven is acting strangely, twice in the past couple months it’s said it preheated to set temp (400*) and in reality it never went past 150* measuring by a thermometer I keep inside. I reset the breaker and it started working again. Like I said that’s happened twice in 6 months, but I’m also noticing that everytime I turn it on it will say it’s preheated (beep noise) anywhere from 75-150 degrees lower than it’s set for, but does eventually continue to climb...

Read more

via Bosch HBL3350UC/09 oven says it’s preheated 75 degrees or more before it is
by Bepding

Dacor ER48DSCH/LP Baking Temperature Won't Regulate

The Issue - My Dacor ER48DSCH/LP dual fuel range large oven temperature won't regulate after installing a new bake element. When the oven is turned on and a desired temperature keyed in, the temperature climbs into the 500's. At that point I shut it down. There are no error codes and the small oven works fine.

Background - The range is about 11 years old and the original relay board was replaced by me about 4 years ago. The original one was sent out to be repaired but hasn't yet...

Read more

via Dacor ER48DSCH/LP Baking Temperature Won't Regulate
by doxiedad

Bosch HGI8054UC/06 Gas range burner screw

Hello All,

I wanted to replace the burners on the cooktop, since they were sort of discolored. Got new ones and while screwing one of the burners, I used too much torque and damaged the T20 screw-head; I am unable to get it out now. The ignitor is standing far too tall now to place the burner plate..Are there any instructions to remove the cooktop and access underneath to remove the screws. My first step is to try a damaged screw extractor. Assuming I get it out..each new screw is $16.00...

Read more

via Bosch HGI8054UC/06 Gas range burner screw
by carybimmer